• 350.000+ tevreden klanten
  • 2.500.000+ technische artikelen
  • Voor bedrijven én particulieren
  • Vanaf € 6,95 verzendkosten
  • Achteraf betalen
  • WebwinkelKeur-cijfer: 9,4

Timken Kegellager - 3743137625 | 109.538 mm | 158.75 mm | 21.438 mm | 15,875 mm | 23.02 mm | 3,5 mm | 3,3 mm

Artikelnummer: 3743137625 | Snelcode: 39uf

Deze productfoto's zijn indicatief en kunnen afwijken van het daadwerkelijke product.
De titel, omschrijving en eigenschappen van dit product zijn bepalend.

10% korting
€ 441,00 € 400,76
Per stuk, inclusief 21% BTW
€ 331,21 per stuk, exclusief 21% BTW

Actuele verzenddatum controleren
€ 6,95 verzendkosten
Voor bedrijven én particulieren
Achteraf betalen
    Artikelnummer 3743137625
    Merk Timken
    Verpakkingseenheid Per stuk
    Snelcode 39uf
    EAN / GTIN 0053893709420
    Andere artikelnummers 3743199401, TIMKEN3743137625
    • Tractor
    • Landbouw
    • Aandrijftechniek
    • Oogsttechniek
    • Lagers en lagerhuizen
    • Voorasdelen 4WD
    • Vaste 4WD vooras
    • Vierwielaandrijvingsas, star
    • Kegellagers en cilindrische rollagers
    • Kegellagers
    • Inch series - compleet (gesorteerd op afmeting)
    • Inch series - compleet (gesorteerd op artikelcode)
    • Achteras vierwielaandrijving
    • ProVoorasdelen 4WD
    • Geveerde 4WD vooras
    • Passend voor deze modellen
    • In deze categorieën
    • In deze overzichten

    Omschrijving van Timken Kegellager

    per stuk
    d (mm)
    109.538 mm
    D (mm)
    158.75 mm
    B (mm)
    21.438 mm
    15,875 mm
    T (mm)
    23.02 mm
    Max. as radius R
    3,5 mm
    Max. huis radius r
    3,3 mm
    Vraag en antwoord

    9 beoordelingen

    Maurice D. op 13-07-2021
    Werkschoenen zijn van goeie kwaliteit en lopen ook prettig
    gloryglo op 14-07-2020
    Excited to find these. The box for these has a 2016 date, so I assume they have been discontinued. All I can find in stores now are zinc or brass. From my past experience, the metal ones corrode. And yes plastic has a limited lifetime too, but I prefer these over the metal ones. Again I was very excited when I found these online for sale, and have been very pleased with the performance of them. Not only that, but now I have backups! Probably for years...
    MATTHEW op 26-06-2020
    Was looking for an American made bearing kit for the boat trailer and couldn’t find one, had to piece together my own. Bearings itself seems fine, no complaints yet, however very little use so far, (Maybe 75 miles)
    jbun8388 op 15-06-2020
    This is whats needed to support the small roller bearings that that fit on the outsides of the rim. ( front and back of wheel ) The cage bearing supports the center of the wheel surface and keeps the spindles from wearing on the outsides. Put a 1/8" pipe plug in to replace the grease zirk on the wheel. Pre-pack the cage bearing and slip it into the center of the wheel. Then replace the outside bearing and install back on tractor. Sealed bearings on the oursides of the cage, will protect it from the elements.
    marv op 11-03-2020
    Used these to make setup bearings for my axle rebuild. These mic out about half a thousandths short. Then I installed timkens.
    BRIAN op 07-02-2020
    Great part fit like a glove . was a real pain in the butt getting to the house . Managers would not call back after leaving three messages had to go back to the store to get transaction handle correctly.
    69Camaroguy op 26-12-2019
    This race also fits the rear swing arm on a late 1970's Harley Davidson Sportster. That is what I used it on and it fits perfectly because that's what was used by the factory. Cheapest place I could find one.
    EDW op 25-10-2018
    Ik woon in deze laarzen. Heerlijk comfortabel werkschoeisel. Maar waar ik nog het meest blij mee ben is dat ze mijn voet gered hebben van fracturen nadat ik met m'n voet onder een heftruck van 4 ton kwam. Geen enkele breuk. Wel flinke scheurwond door de druk en bont en blauw maar mijn tenen niks ...heel bizar!
    Edward op 25-07-2017
    I bought these along with 1ASHS00971 wheel bearing set to replace both sets of bearings in the front hub of my 2003 Nissan Xterra SE 4X4. These were an exact fit and a great quality. I highly recommend having the proper tools when removing the old race's and installing the new one's. Fortunately I have a friend who is a mechanic and let me borrow his tools for this. The only other thing you will need to buy is a good quality wheel bearing grease to repack them and the hub when installing them.
    Bekijk alle 9 beoordelingen »
    Nieuwe beoordeling
      1 ster 2 sterren 3 sterren 4 sterren 5 sterren